Home » Programs » Service Plans » Natural Gas and Propane Plans

Simplify maintenance with CHS Natural Gas and Propane Plans

Routine maintenance is the best way to keep your natural gas and propane equipment running at its best – and to spot common issues before they require costly repairs.

CHS Natural Gas and Propane Plans are a great way to simplify routine maintenance. Available at two pricing levels – Priority Plan (ideal for newer and well-maintained systems) and a more comprehensive Ultra Plan (better for older systems, or for more peace of mind) – these plans will take the worry and hassle out of keeping your natural gas equipment running at its best.

See below for more details on what each plan covers. And don’t forget: You can also get CHS Service Plan coverage for your gas-fired water heater – or coverage for additional home comfort equipment via our other home service plans!

Priority Plan

Your CHS Priority Plan coverage includes:

  • A 15-point tune-up performed once during the service agreement term during regular working hours. Contact us to schedule yours.
  • 15 percent off all repairs
  • 15 percent off diagnostic fees
  • No after-hours charge

Ultra Plan

Your CHS Ultra Plan coverage includes:

  • A 15-point tune-up will be performed once during the service agreement term during regular working hours. Contact us to schedule yours.
  • Priority Service
  • No diagnostic fee
  • No after-hours charge
  • Repair coverage for more than 35 parts in your system

Loyalty Credits

Save even more with CHS Loyalty Credits

For each consecutive year you are enrolled in our Priority or Ultra Service Plan, you earn $50 in Loyalty Credits. You can accumulate up to $700 in credits and apply them to equipment purchased from us, including:

  • Boiler (up to $350)
  • Furnace (up to $350)
  • Central AC system (up to $350)
  • Heat pump (up to $350)

Priority Plan

Your CHS Priority Plan coverage includes:

  • A 15-point tune-up performed once during the service agreement
    term during regular working hours. Contact
    us     to schedule yours.
  • 15 percent off all repairs
  • 15 percent off diagnostic fees
  • No after-hours charge

15-Point Tune-Up

  1. Test carbon monoxide levels
  2. Clean and adjust burners and inspect heat exchanger
  3. Check thermostat operation
  4. Lubricate all motors, bearings, fans and circulator pumps
  5. Clean pilot assembly
  6. Test and adjust operation of safety and operating controls
  7. Inspect flue pipe and gas valve
  8. Clean and check blower motor (and belt if applicable)
  9. Test and tighten all wiring and connections
  10. Turn exposed dampers to heating position if marked (no
    balancing)
  11. Flush condensate drain to protect against overflow
  12. Check temperature rise
  13. Check fan speeds
  14. Check gas pressure at gas valve
  15. Inform customer of equipment condition; recommend necessary
    repairs

Ultra Plan

Your CHS Ultra Plan coverage includes:

  • A 15-point tune-up will be performed once during the service
    agreement term during regular working hours. Contact
    us     to schedule yours.
  • Priority Service
  • No diagnostic fee
  • No after-hours charge
  • Repair coverage for more than 35 parts in your system

System Parts

  1. Blower belt
  2. Blower motor (1/3-3/4 hp; psc only)
  3. Blower motor pulley
  4. Circulator coupling (1 zone)
  5. Circulator motor
  6. Circulator relay
  7. Combination control
  8. Draft inducer motor
  9. Emergency switch
  10. Fan and limit control
  11. Flue pipe
  12. Gas valve
  13. Glow ignitors
  14. High limit control
  15. ICM control board
  16. In-line draft diverters
  17. Low limit control
  18. Low voltage transformer
  19. Pilot assembly
  20. Pressure switch
  21. Pressuretrol
  22. Primary control
  23. Reverse aquastat
  24. Rollout switch
  25. Single aquastat
  26. Spill switch
  27. Thermocouples
  28. Thermostat (nonprogrammable)
  29. Triple aquastat

Gas Burner Parts

  1. Burner orifice
  2. Gas valve orifice
  3. Pilot tube
  4. Sensor
  5. Sensor ignition module

Other parts

  1. Altitude and temperature gauge
  2. Thermostat sub base

Services

  1. Carbon monoxide testing

15-Point Tune-Up

  1. Test carbon monoxide levels
  2. Clean and adjust burners and inspect heat exchanger
  3. Check thermostat operation
  4. Lubricate all motors, bearings, fans and circulator pumps
  5. Clean pilot assembly
  6. Test and adjust operation of safety and operating controls
  7. Inspect flue pipe and gas valve
  8. Clean and check blower motor (and belt if applicable)
  9. Test and tighten all wiring and connections
  10. Turn exposed dampers to heating position if marked (no
    balancing)
  11. Flush condensate drain to protect against overflow
  12. Check temperature rise
  13. Check fan speeds
  14. Check gas pressure at gas valve
  15. Inform customer of equipment condition; recommend necessary
    repairs

For everything you need in home heating, trust the pros at Carroll Home Services – keeping Maryland homes warm for more than a century! Contact us to get started today!