15-Point Annual Tune-Up

A tune-up will be performed once during the 12-month plan period Monday through Friday during normal business hours. Please call to schedule the tune-up, which includes the following:

1. Clean heating unit, flue, pipe and chimney base.
2. Adjust burner for maximum efficiency.
3. Clean and adjust electrode and nozzle assembly.
4. Lubricate all motoors, bearings, fans, and circulators.
5. Replace oil nozzle and oil filter.
6. Test and adjust all safety and operating controls.
7. Inspect flue pipe, barometric damper and combustion chamber.
8. Test oil pump operation.
9. Change air filters (customer must provide).
10. Check oil tank and lines.
11. Clean pump strainer.
12. Perform efficiency test.
13. Drain expansion tank, if necessary.
14. Inform customer of equipment condition.
15. Recommend necessary repairs.

Parts Covered (including labor):

 

Controls:

• Blower circuit board
• Burner mount relay
• Cad cell control
• Circulatory relay
• Combinatino control
• Double aquastat
• Draft regulator
• Emergency switch
• High limit control
• Hydraulic jack
• Low Limit Control
• Pressuretrol
• Primary control
• Reverse aquastat
• Single aquastat
• Stack control
• Thermostat (manual)
• Triple aquastat

Warm Air System:

• Air diffuser
• Air regulator
• Blower bearings
• Blower Belt
• Blower Motor (up to 1/3 hp)
• Blower Motor Pulley
• Blower wheel
• Blower mount relay
• Power vent motor

Hot Water / Steam System:

• Automatic air vents
• Automatic water feeder
• Circulator bearing assembly
• Circulator Coupling
• Circulator gasket
• Circulator impeller
• Circulator Motor
• Circulator motor mounts
• Circulator wicking
• Complete Circulator
• Dual valve
• Fan and limit control
• Gate valves
• Gauge glass
• Glass gauge washer
• Globe valve
• Mixing valve
• Pop safety valve
• Zone valve complete
• Zone valve power head

Oil Burner Parts:

• Air shutter
• Air stabilizer
• Burner Air Tube
• Burner capacitor
• Burner coupling
• Burner Fan
• Burner flange gasket
• Burner housing assembly
• Burner master control
• Burner Motor
• Burner porcelains
• Buss Bar Leads
• Cad Cell Asembly
• Cad Cell Eye
• Delayed oil valve coil
• Electrodes
• End Cone
• Ignition leads
• Ignition transformer
• Low Voltage Transformer
• Nozzle
• Nozzle Adapter
• Nozzle line
• Solenoid Coil
• Solenoid valve
• Turbulator

Fuel Supply Parts:

• Firmoatic Valve
• Flare fittings
• Fuel Filter Cartridge
• Fuel Pump
• Fuel pump bleeder
• Fuel Pump Gasket
• Fuel Pump needle valve
• Fuel Pump Seal
• Fuel pump strainer
• Oil Line Fittings

Other:

• Fill Cap
• Flue Pipe
• Vent Cap
• Tank Gauge (if enrolled in Carroll's Automatic Fuel Delivery Program)

^*Plan covers hot water parts listed for the main living area only. Additional circulators, thermostats and zone valves can be covered for an additional charge. Call for details.

15% discount on all other parts

Loyalty Credits

It is our goal to reward our loyal service plan customers! For each consecutive year you renew your service plan, you earn a $50 credit (up to a maximum of $700 per plan). You can use all or a portion of these credits toward the purchase of heating and cooling equipment. Credits are not transferable to other homeowners, and they cannot be transferred from one plan to another. They have value only as credit toward the following equipment purchased from Carroll Home Services:

• Boiler $500
• Furnace $350
• Humidifier/Air Cleaner $100
• Heat Pump $350
• Central A/C System $350

General Conditions for Burner Plans

Any pre-existing conditions will be serviced at prevailing rates. Performance under this Agreement by Carroll is contingent upon Customer purchasing his entire fuel oil requirements from Carroll and upon Customer's fuel oil account being current at all times. Carroll Home Services will repair or replace, during the life of this agreement, at no extra charge, all parts listed above that may become defective due